Mechanical

This is a unique style, heavy duty slip joint Channellock pliers marked CHAMPION DEARMENT MEADVILLE PA. U.S.A. CHANNELLOCK NO. 410 REG. U.S. PAT. OFF . They measure 9.5 long and are very heavy duty with jaw width of .45 . Lots of very good jaw teeth, shaped somewhat like a pipe wrench. They have about a .75 capacity between the jaws. The handles are plain, no cast grip patterns on them. Overall in very good condition with the exception of some very minor pitting in a few small areas noted. No rust or damage to report. Top quality, heavy duty, vintage pliers!

This is a unique style, wide mouth tinner's pliers with the 1 wide mouth, and the mouth jaw are flat 1.2 back from the end inside jaw measurement. They are 7 long overall. The inside handles are marked in raise cast lettering, KNIPEX MADE IN GERMANY . This is a very nicely made cast steel pliers in very good condition with no rust, very little wear or sign of use, good straight jaws, and snug pivot pin! Nice quality!

Offering this nice clean 6.0 long overall wing divider marked H.S.B. CO. REVENOC MADE IN U.S.A. 6 on the side of one leg. This one is in good used condition, no rust, good thumbscrews, threads, and spring, and has good sharp points, ready to use. We do note some minor pitting on the larger round parts of the legs, doesn't effect use. Features the fine adjustment, brass and steel pivot joint.

This is a Stillson wrench with the REGESTER STILLSON TRADE MARK WALWORTH MFG. CO. BOSTON, U.S.A. on one side, and is also marked 8 in several places on it. It measures about 7 long closed. This one is in very good useable condition with some steel chips and wear on the jaws teeth, mainly on the adjustable jaw, but enough teeth is there to use it on small pipe. The handle and the jaw at the end of the handle section are in good shape, good spring a good straight bar handle, not bent or cracked, also has a good useable adjustment nut/knurl. This size is becoming had to find in this nice condition.

This is a hard to find crank handle for a mechanical devise of some kind. It is solid cast steel, 5.5 long overall, and has a square drive cut out or slot that measures about .39 square tapering to .35 , designed to press fit onto a tapered square. The crank knob is solid, (isn't designed to spin on it's own) and measures about .9 diameter. A nice replacement handle overall. No rust, no damage. Price is for one, per each handle.

This is a very nice, vintate 14 adjustable pipe wrench, marked CRAFTSMAN 14 GUARANTEED on the handle area, and CRAFTSMAN GUARENTEED HIGHEST QUALITY U.S. PAT. OFF. on the main frame (logo sticker). In good++ condition with minimal wear, no rust, good straight metal and threads, very good spring load adjustable jaw. The jaw edges show very little wear, and the jaws align well with one another, teeth sharpness is very good! Overall, a very carfully used antique wrench by the looks of it! Measures 13.0 long (completely closed) even though it is marked 12.75 on the wrench, and the jaws are 7/8 thick. This wrench is one of the nicest we have seen of it's type in the past 10 years. The handle and main frame have about 90% original blue paint intact, there is no paint on the adjustable jaw. A nice quality wrench made in U.S.A.!

This is a very nice, 15 adjustable nut wrench, marked TRIMO TRIMONT MFG. CO. ROXBURY MASS. U.S.A. TRIMO SIZE 15 PAT'D 12-19-1911 on the handle area, and DROP FORGED on the moving jaw. In good++ condition with very little wear, no rust, good straight metal and gears. The jaws edge show very minor wear, minor dings on the edges, but much better than most, and the jaws align well with one another. We note a few small hammer dings on the end of the handle, otherwise a very carfully used wrench by the looks of it. The knurled thumbwheel design works great as it incorporates a stamped steel U shaped washer, (formed to fit into the main casting for smoother operation) that helps the thumb wheel turn much easier, and also guides the moving jaw better) than those without this feature. The washer is formed to fit into the main casting next to it, so it doesn't spin round and round. A very nicely designed hard to find size, nice clean wrench, from the early 1920's era. Measures 13.6 long (completely closed) even though it is marked 15 on the wrench, and the jaws are 1.0 thick.

This is a nice clean knife handle type, adjustable monkey wrench with the two piece wood (metal center section) handle. It has a little wear on the jaw edges, some minor dings on the jaws mostly, a nice straight beam and jaws, with good jaw alignment, nice solid handle, no cracks, very tightly attached, no rust or cracks on the steel. It's marked Coes Wrench Co. Worcester Mass. U.S.A. , and also stamped MFG. UNDER COES PAT'D STEEL. A nice clean wrench overall! 12 inch length. ADD $10.00 SHIPPING TO ANYWHERE IN THE U.S.A.

This is a rare antique thread repair tool, for repairing outside threads on machine bolts or screws. The tool is hardend around the threads so you can run the screw into on of the threaded holes on the thread plate to cause damaged threads to be forces back into the same thread pattern has they once were. Not a common tool, in fact very rare in this size. The threaded holes range from around 1/16 to 3/16 , and the thread per inch appear to be standard national course threads. The tool is shaped much like a spatula so the handle give clearence in the event of a screw stud extending upward from a flat plate needing repaired, in this case the user can use the leverage of the handle without interference with the stud plate. The thread all check out good except for the largest one has some tiny chips off at the thread start point. As you can see there is also some pitting on the steel, otherwise no damage, no rust, clean. A rare thread screw plate tool!

This is a nice clean Schollhorn antque end nippers in good useable condition. It is marked BERNARD'S PATENT OCT. 24 1899 W.SCHOLLHORN CO. NEW HAVEN CT. on the side and there is also a logo of a dog running with the name BERNARD inside the logo on one handle. The cutter jaws are in very good condtion with little wear, quite sharp, they measure .9 wide, and the tool is 6 long overall. We do note that we see no rust, however there is some minor pitting in a few small spots. This model has a clearance hole that goes throught the center of the jaw movement assemblies, so 3/32 wire can be cutter several feet into the length of wire, allowing for a good square cut. The handles both have a good strong spring load on them forcing the jaws opened. A very nice smaller size end nipper overall!

This is a nice clean U.S.A. made 12 vernier caliper with .001 inch graduations on both side of the caliper (one side is for outside measurement scale, the other side for inside measurement, each marked accordingly), in the original custom hardwood case. It's marked BROWN . The calipers are in very good shape with the exception of the grind marks on the one side of the carrage or moving jaw and fine adjustment sections. I am not sure, but I assume this was the past owner's idea of a owner's mark. At any rate, it doesn't effect use, or accuracy of the caliper in any way. They have the fine adjustment feature in very good working order, and they have hardened jaws. There is very little wear, moves very snug on the frame. The fitted case is solid with good latches and hinges, it has some minor wear, a some small scrapes on the top, in solid condition with good velvet inside the fitted case. It is also marked on the exterior top, BROWN in gold/black lettering. A nice clean machinist tool!

Large antique iron plumb bob. It is in good condition. It is quite hefty for it size which is 4.75 long x 6.5 around body. A great manly gift for the antique tool collector! Some people frame assortments of these in shadow boxes and hang on the wall. 9/10utcs

This is a very nice clean antique plumb bob marked K+E 830006 on the top thread cap section. This is well known tool and instrument maker (Keuffel long, 12 ounces, 3 pieces, with a good steel tip, both ends are thread, good threads. The neck area is threaded at the flair of the plumb bob, or in other words that neck piece is 1.0 long plus the threaded part that is inside the main body and can't be seen in the pictures. It's in nice shape! Some tiny dings noted, otherwise minor wear. The neck is 1.0 long x .5 diameter. A nice collectible plumb bob!

This is a very rare, very nice clean antique plumb bob marked G. W. LEACH on the top thread cap section. This is an unknown maker to us, not sure where it was made, but it could also be the name of the surveyor that owned it at one time. I have never seen another plumb bob with this name on it. This one is 6 long, 16 ounces, 3 pieces, with a good steel tip, both ends are thread, good threads. The steel tip has just a little pitting on it, but not at the point. The neck area is threaded at the flair of the plumb bob, or in other words that nech piece is 1.25 long plus the threaded part. It's in nice shape! Some tiny dings noted, otherwise minor wear. The neck is 1.25 long x .56 diameter. A very hard to find collectible plumb bob!

This is a very rare, very nice clean antique plumb bob marked B-M-CO. ELIZ. N.J. U.S.A. on the top thread cap section. This tool company (Braunsdorf-Mueller Co.) was in business from 1888-1910, making top quality precision tools and instruments. I have never seen another plumb bob with their name on it in several years. This one is 6 long, 12 ounces, 3 pieces, with a good steel tip, both ends are threaded, good threads. It's in nice shape! Some dings noted, mostly at the top of the cone shape, otherwise minor wear. The neck is 1.5 long x .50 diameter. A very hard to find collectible plumb bob!

This is a U.S.A. made 6 monkey wrench marked P.S. on the solid jaw. It's in good condition, not rusty, with a good solid wood handle and a straight bar. The jaws have some wear, but a straight, some minor edge dings noted, good threads and slide. A nice small size antique adjustable monkey wrench!

Have a Yankee Spiral Ratchet Screwdriver? Need a hex/Allen/Torx head bit for it? This adapter is for standard Hex drive bits, giving you the ability to use hex head (short bits) like the ones in the include set. This adaptor is made in the USA and comes in three sizes on the Yankee connecting end, this one is .312 (5/16 ) diameter for the Yankee 31A, 131A and some other models by Yankee and other makers, like Millers Falls, and Greenlee, large size models as well. I also have a smallers shank size availiable at this website. On the hex end there is a coil spring the grasps the hex bit when it is inserted keeping it from falling out. (Don't use bits that are stepped down as they will become stuck in the adapter. Small knotches are fine, like the ones shown in the pictures. This set includes 7 different Torx sizes, (T-10 to T-45), and 6 different Allen Head or Hex head sizes (5/32 to 3/8 ). A real nice addition to your bits for a Yankee screwdriver! Shipped in the contental U.S.A. is $3.00.

Have a Yankee Spiral Ratchet Screwdriver? Need a hex/Allen/Torx head bit for it? This adapter is for standard Hex drive bits, giving you the ability to use hex head (short bits) like the ones in the include set. This adaptor is made in the USA and comes in three sizes on the Yankee connecting end, this one is .280 (9/32 ) diameter for the Yankee 30A, 130A and some other models, like the Millers Falls 61A, as well. I also have a larger size availiable at this website. On the hex end there is a coil spring the grasps the hex bit when it is inserted keeping it from falling out. (Don't use bits that are stepped down as they will become stuck in the adapter. Small knotches are fine, like the ones shown in the pictures. This set includes 7 different Torx sizes, (T-10 to T-45), and 6 different Allen Head or Hex head sizes (5/32 to 3/8 ). A real nice addition to your bits for a Yankee screwdriver! Shipped in the contental U.S.A. is $3.00.

This is a very nice, used 1/2 capacity ball bearing super chuck marked JACOBS U.S.A. 14N 3 JT SCV. KIT #30345 1/8-1/2 IN 0-13mm CAP. near the jaws, and also marked JACABS BALL BEARING SUPER CHUCK around the chuck sleeve at the 1/2 diameter arbor end of the chuck body. The arbor has a few scratches noted, none effecting used, no sign of damage or abuse. We also note a past owner's name on the end cap plate on the chuck. The ball bearing movement operates very smoothly with little effort, and no binding. The jaws are in very good condition, no sign of wear. Comes with a nice chuck key. The key is also marked JACOBS #3 KEY on it. A very nice used precision drill chuck overall!

This is a nice antique, 14 adjustable pipe wrench, marked 14 USHCO LAWSON U.S. HAME CO. BUFFALO N.Y. U.S.A. PAT. DEC.14.20 OTHER PATS PEND . This is a rare pipe wrench with a angled knurl slot patent that used gavity instead of moving jaw spring load to keep the moving jaw in it's proper position. Works good! In good+ condition with very little wear, no rust, very good jaw teeth, knurl thread and jaw gears. The jaws show very little wear overall. We note a few small hammer dings on the the handle, and the handle is slight bend on it's width, not noticeable if laying flat or hanging on a wall, otherwise a very carfully used wrench by the looks of it. Measures 13 long (completely closed) even though it is marked 14 on the wrench, and the jaws are 3/4 thick. A very rare and collectible patented antique pipe wrench!

This is a very nice, 12 adjustable nut wrench, marked TRIMO TRIMONT MRG. CO. ROXBURY MASS. U.S.A. TRIMO SIZE 12 PAT'D 12-19-1911 on the handle area, and DROP FORGED on the moving jaw. In good++ condition with very little wear, no rust, good straight metal and gears. The jaws edge show a few dings on the edges, but much better than most, and the jaws align well with one another. We note a few small hammer dings on the end of the handle, otherwise a very carfully used wrench by the looks of it. The knurled thumbwheel design works great as it incorporates a stamped steel washer, that helps the thumb wheel turn much easier than those without this feature. The washer is formed to fit into the knurl so it doesn't spin round and round. A very nicely designed hard to find size, nice clean wrench, from the early 1920's era. Measures 11 long (completely closed) even though it is marked 12 on the wrench, and the jaws are 3/4 thick.

This is a good, used, 8 inch long pliers marked UTICA 1000 UTICA N.Y. U.S.A. with the antique 3 diamonds logo. The jaws, and all three wire cutting sections are in good shape. As you can see in the pictures, there is some minor wear on the outside of the jaws mostly, the inside jaw grips, and cutters are in very good shape overall. There is a few dings around one side of the pivot area noted, but no cracks, no rust, or other damage. A quality made used pliers by a well known tool maker!

This is a good used No. 73 inside caliper, with the solid fine adjustment nut. This caliper is in very good condition overall with no owner's names, no noted wear, no rust, some minor darkening on the finish, a few tiny pitted area, very good tips joint and spring. It is marked THE L.S. STARRETT ATHOL MASS. U.S.A. on one side.

This is a very good used No. 73 inside caliper, with the solid fine adjustment nut. This caliper is in very good condition overall with no owner's names, no noted wear, no rust, fine condition overall. It is marked THE L.S. STARRETT ATHOL MASS. U.S.A. on one side.

This is a very nice clean, 18 long STILLSON pipe wrench marked STILLSON WRENCH MFG. BY HENRY in cast lettering. This one has been used, but overall is in very good working order, not bent, cracked or otherwise damaged, a small hammer dings on the handle area, jaw area is very good, very good jaw teeth, two good springs, good knurl and gear teeth, adjusts just fine, no rust, no pitting, good pivot joint, with no original intact, no rust, no pitting, useable condition. This is a good antique wrench made about 100 years ago.

This is a very scarce 18 pipe wrench marked 18 MASTERENCH CHROME VANADIUM on one side, and PATENTED 4-14-23 , and has the standing horse logo also. MASTERENCH . The trade name sounds like Masterwrench, but the W is dropped in the actual name. The Heller name has been partially ground off but enough there to confirm the maker is Heller. We have seen only one other in this size in the past ten years in anywhere near this good of condition, as the 18 size is rare. This one has been used very little, has a very good pivot joint, and the double spring is still in good working order, so the jaw returns to the closed position as it is suppose to. The jaw teeth are very nice, only minimal wear. The jaw is .99 wide. There is no rust on this wrench, no cracks, no bent areas, very nice. The finish is a darkened finish, has some minor original casting imperfections, but those are on the handle section, and will not effect use. A good straight, hard to find, collectible adjustable wrench!

This is a nice clean, vintage 3-jaw drill chuck marked THE JACOBS MFG. CO. HARFORD CONN. MADE IN U.S.A. JACOBS DRILL CHUCK PAT. 1902 NO. 34 1/2 CAP. . It's has 5/64-1/2 CAPACITY, is in very good working condition with very good jaws, adjusts smoothly, appears to have been used, but very little wear, however, we do note some dings on the end plate where the arbor will fit, and a few on the end plate where the jaw slide in, but no effect on use, stricktly a cosmetic issue. It is designed to be fitted with an arbor that has a 5/8 tapered end at one end to fit into the precision hole on this chuck. These arbors are still available for sale by Jacobs. The key for the chuck is included, and is in very good condition.

This is a clean and rare example of a patented 10 spring loaded lever adjustable pipe wrench, marked .R_AND PIPE WRENCH CO. BOSTON MASS. U.S.A. PAT. JULY 7-SEPT.22.1903 OCT.3.1905 . This unique wrench has a lever on the handle that is spring loaded, and is basically self-adjusting after you push the lever to the handle and set the wrench in place on the pipe. The serrated jaws are in very good condition, with minimal wear noted, we do note a small casting flaw or small chip at the very end of the adjusting jaw, will not cause any use issues. We think it is a casting flaw since we had another one with the exact same flaw on it. The spring load is still plenty strong, and the lever action works great! The wrench measures 11 long, with .7 wide jaws. The handle is thick walled pipe material. Very little minor pitting is noted, no rust. The two pivot joints are in great shape, the jaw joint is very snug, the lever jaw a little looser. A nice, rare wrench! There was 3 patented asigned to this wrench, Sept. 22,1903, July 7,1905 & Oct. 3, 1905. It is also Schulz #681. A very hard to find, collectible lever action adjustable pipe wrench!

This is a nice clean 17.5 long, two speed breast drill marked CRAFTSMAN MADE IN THE U.S.A. on the crank handle, but made by GOODELL-PRATT COMPANY TOOLSMITHS GREENFIELD MASS. U.S.A. PAT. MAR. 31.1896 . This one has a rather unique speed selector, as you can see a wide knurled thumb wheel in the gear section area. To shift gears requires a simple movement of this wheel for slow or fast. Both speeds and all gears are in very good working condition, This is a rare and unique breast drill! We have not seen this type speed selector on any of the other Goodell-Pratt models over the years. The crank wheel is 5 diameter, but shaped differently than other models from this period, as there is an inside flat ring that rides on a ball that sets on a post off the frame, to help keep the wheel balance and running true to the gears being meshed during use. There is about 30% paint intact on the wheel, but not rusty or pitted, the frame and the breast plate have about 40% paint intact. The 3 jaw chuck is also different than most other Goodell-Pratt models from this era, is is longer, and no patent date on it, but is is spring loaded on the jaws, runs true, and has a 1/2 diameter capacity. The wood handles are intact, no cracks, minor wear, nice finish, no metal cracks or damage. This is a very rare breast drill in very good working order! As a note of interest, Millers falls took over production of this model when they bought out Goodell-Pratt around 1914, at that time this model became Millers Falls No. 99A.

This is a nice antique set of pipe thread cutting dies, and some standard thread dies also, including the threader in the rare smallest No. 1 smaller size on good++ useable condition overall. It includes 10 sets of adjustable dies that all fit the die wrench including this sizes in pipe dies; 1/8 , 1/4 x (2), , dies, each has a custum size guide ring that keeps the pipe or stock running true or square to the dies while threading. The standard thread dies are as follows: 1/4-20, 5/16-18, 3/8-14, 7/16-14, 1/2-13, 5/8-11, 3/4-10. Also included is two pipe handles for the threader (each are 7.0 long), one wrench, (for the bolts on the die wrench, and 9 different sized ring guides (sized to fit each die set). These die inserts are in good condition, but show wear, one of the 1/4 dies has small chips in a critical area, will be good for chasing threads, but most likely would not cut threads, the rest will cut new threads (included is 2 set, this size, so one set is in much better condition). Replacement dies for this size may be hard to find, as they are smaller in size than the much more common No. 2 size. The No. 1 dies in this set fit into a slot that is only 1 wide. The threader is marked F. ARMSTRONG BRIDGEPORT CT. 1 MADE IN U.S.A. and is in very good condition with some oil residue, but generally very clean, nice quality casting, and a unique pair of hearts cast into the wrench head near the name. The dies have good thread leads and cutting areas, but they show there age and show signs of being a bit brital as there are small chips off most of them, still useable, the chips are mostly on the back end or on the opposite side of the lead threads. These are the adjustable size type dies, that will allow the user to vary the size by about 1/32 to fit pipe to close tolarances. The threader casting alone is 6.5 long overall without the handles, they are 7.5 long overall each, all in very good shape, good threads. The box is one of the nicest we have seen, lap jointed in the corner, made of oak, has a darkened natural finish on it, good stong, well attached hinge wires, There is one stamped marking on the end of the outside of the bottom (end label) of the box that reads, GENUINE ARMSTRONG NO. 1 1/4 to 3/4 BRIDGEPORT CONN MADE IN U.S.A. , plus there is a inside label press into the inside top of the box. The latch is in good shape. The top lid is oak, and in good++ condition, not cracked, minimal warpage. All appears original, some small dings, mostly minor considering the environment this tool was used in. The box is 3.0 x 6.3 x 15.75 . A nice old, small set F. Armstrong Mfg. Co. was in business from 1875-1922 according to research. A rarely seen example of their quality small size pipe threading set! This is one of the few we have seen in the No. 1 size with the standard threads, these are almost alway pipe threaders, so this is a very rare antique set overall!

This is a very nice clean 3-4 size micrometer with .0001 graduations. It is marked SCHERR-TUMICO INC. ST. JAMES MINN. U.S.A. 3 TO 4 IN. on the satin chrome plated thimble. It is also marked in 5 places on the black texture painted frame with various previous owner's numbers, otherwise the paint is about 99% intact. This micrometer is in very good shape with over 95% of the textured paint intact, very little minor wear, was inspected and calibrated, found to be in fine working order. The friction brake and ratchet works just fine also. Also included are the calibration wrench and gauge (rod) in very good shape, and the nice hardwood hinged two piece case or box with a nice finish overall, some wear, a few past owner's numbers on it, good hardware, and is also marked by the maker, matching the micrometer. A very carefully used micrometer, made by a very well known quality toolmaker!

This is a nice, clean, used speed indicator/tachometer. It will gauge rotations Per Minute from 30 to 12,000, and will also gauge Feet Per Minute with the use of the 1 foot circumference wheel that is included. The dial face is 3.25 diameter, and reads HERMAN STICHT CO. INC. NEW YORK N.Y. NO. 586340 SWISS MADE 303 on the face. The main body is all cast metal and has 5 different ranged that you can set by simply adjusting the black dial near the spindle of the unit. The outside of the case is about 99% like new, very nice original lime green paint, no cracks or names scratches on it. Overall the indicator is in fine condition, as the tips show very little wear, all fit very well. The tachometer checked out just fine, smooth operation, smooth range changes, and was drip oiled in several places before use (as recommented). Also included in the case are 6 tips and one 3 extension, and a glass oiler and oil tube are found in the two aluminum vials you see in the left corner of the case. There is also complete instructions with matching model information on them. The case is very nice, green leather like cloth covered hardwood, solid with nice hardware, very light wear, also marked by the importer (STICHT) in gold gilt lettering on the top of the case, overall very good, to fine condition. A hard to find, very nice example of a quality made tool!

Offering this nice clean antique monkey wrench in with a good hardwood handle in good+ working condition. It's marked W . The W long overall. There is a few dings, no rust, but overall a very nice clean heavy duty adjustable wrench with a good solid handle that has no cracks, no damage, nice smooth darkened finish. We note the past owner stamped two intials on the side opposite the maker's mark. A rarely seen, well marked monkey wrench!

This is a very nice, clean, single speed hand drill marked CRAFTSMAN MADE IN U.S.A. but was actually made by MILLERS FALLS CO. No. 77 is the model number. This is a rather rare No. 77 model with the cast frame designed to enclose the gears and spindles! This version is 12 long overall. The drill is in nice shape with about 70% of the original paint intact, and a nice finish on all 3 hardwood handles, but some minor dings and wear noted, not cracked all fit and function as new. The gears, and all the shafts are in great shape, turns smoothly. This model has two driver gears that make contact with the driver wheel gears, very smooth operation. The 0-3/16 diameter capacity, 3 jaw chuck, the jaw have good springs on each jaw, all in great shape! A very nice, hard to find model hand drill tool overall!

This is a very nice wing divider marked by the maker, PEXTO MADE IN U.S.A. 10 made by PECK, STOW, long as show in the pictures, it has been shortened by sharpening the points over the years. There is some minor pitting, a few dings and scratches noted, but none effecting use, no rust, points are sharp and in very good condition overall. We do note a past owner's name stamped on one side also. A very nice design with the fine adjustment feature. The points are sharp and the joint is snug, all the adjustment work correctly as intended. Shows signs of use, but still in very good working order!

This is a very nice wing divider marked by the maker, PEXTO MADE IN U.S.A. 10 made by PECK, STOW, long as show in the pictures. There is some minor staining noted, a few dings and scratches, but none effecting use, no rust, points are sharp and in very good condition overall. We do note a past owner's name stamped on one side also. A very nice design with the fine adjustment feature. The points are good and the joint is snug, all the adjustment work correctly as intended. A hard to find larger capacity model very nice used condition overall!

This is nice clean tap and die set in a fitted wood box that is not marked by the maker, however it contains a die wrench marked O.K. MADE IN U.S.A. NO. 751 and a tap wrench marked NO. 328 GTD MADE IN U.S.A. 27 . Most of the taps and dies are also marked GTD and the various size that they are on them also. The sizes of the taps are from(3-48 to 1/4-20)these are the tap sizes: 3-48 (2), 4-40 (1), 5-40 (2), 8-32 (3), 10-32, 10-24 (2), 12-24 (2), 1/4-20 (2), 1/4-28 (2), as you can see there is more than one of some of the taps. The adjustable round dies, are (3-48, 5-40, 8-32, 10-24, 12-24, plus over 6 different tap drills are also included. All are in the wood case, in various pockets cut in the wood box. The set features a very nice quality tap wrench, a good sturdy adjustable guide die wrench. All the taps and dies appear to be in Good+ to fine condition, and the wrenches are in very good condition. The wood case is solid, no damage, minor finish wear, good hinges, and front latch closure. Overall one of the nicest vintage small sizes tap and die sets I've seen, as most of the pieces are marked and appear to be the originals, plus most sets do not have drill bits like this one does! Very complete, very good quality! A rare set in this nice of condition! All the drills, taps and dies are in very good condition, many show no sign of use! The case is 6 x 11.5 with a good latch and hings.

This is a nice clean, antique, set of 12 engraving chisel, all with hardwood handles, all in good sharp condition, and all marked E.C. MULLER N.Y. on the hardened steel. A few have slightly loose handles, otherwise in very good ready to use condition. All the handles have ferrules, some different wood than others, some smaller than others, and some marked with numbers or some sort of mark on the handle. Here is the numbers on the steel chisels themselves 133 12, 11+line65, 65 6, 48, 4, 5, 150 12, 46, 3, 52, 1, the one chisel with the largest trianglar shape is not marked with a number. This is a real nice vintage set of 12, all made by Muller, all in nice clean shape! The set comes with a cloth tool roll that has enough open slots for double the number of chisels than is included in this offer. The roll is in good clean shape with some cloth stains here and there, but suitable for chisel storage. Overall a nice gravers chisel set!

This is a new old stock chrome finish, 10 size adjustable wrench replacement Knurl wheel. This one will fit the older Crescent brand 10 wrenches that are marked Jamestown on them, and perhaps newer ones too. The thickness of the knurl is .62 long, and .56 diameter. Keep in mind that Crescent also made plain finish wrenches were thicker in the jaw area, and had different gears, and threaded wheel (knurl), this one is for the chrome finish wrenches only. We will be listing replacement parts for several sizes of Crescent wrenches, as well as other brands. Ask us if you have any questions.

This is a very nice, clean 6' spring steel folding rule! This one is about 1/2 wide on each section, and has 1/32nds, inch graduations on one side, the opposite side is blank. Much lighter duty than the Lufkin No. 1176 as a comparable rule. It is marked JORDAN GERMANY FINEST SPRING STEEL WARRANTED . This rule has the stamped type double notch lock joints per each section, and this used rule is in very good shape in the joints, and steel sections area, with only a little wear on the graduation markings on the sections, good+ joints. This one has a few tiny areas of very minor pitting, no rust now, some minor darkening, but very clean and useable. We don't see many of these Jordan brand rule anymore these days, particularly in this nice of shape!

Offering this new old stock, Phillips (No. 1 size Phillips) YANKEE screwdriver tip to fit the ratchet screwdrivers like the Stanley or North Brothers YANKEE No. 30, 30A, 130, 130A, and some other brand names also, like Millers Falls, Craftsman, and Greenlee that require a .280 (9/32 ) diameter shank size interchangeable tip that has the flat, and notch on the shank. These are the APEX NO. 451 MADE IN U.S.A. hardened steel tips, for medium size head, 1 PT. Phillips screws. These are 3.2 long overall.

This is a very nice clean 6 foot tape measure. It measures in 1/16ths and 1/32nds graduations, up to 6 feet. The chrome plated body is 2 diameter, and has a strong spring loaded return. The tape is in very good shape, except for a very slight bend in the first inch of the steel flex tape area, the tape otherwise is really nice. This is a push button spring loaded release return. The push button is in the center of the exterior of the chrome plated body, works great, need a drop of oil now and again. The exterior is marked on one side MACHANICS PAL MADE IN U.S.A. 6 FEET and the tap is also marked WALSCO MADE IN U.S.A. SERIAL# R12 Nicely made pocket size tape, in very good shape!

This is a very nice clean Screw Thread calculator copyright in 1935 by THE LUFKIN RULE CO. SAGINAW MICH. U.S.A. COPYRIGHT 1935 L.R.CO. The calculator is two piece, the top round section spins, for finding sizes of tap drills for NC and NF, also NPT on the back side, x 4.75 with a 2.75 diameter round section. It's in very good shape!

This is a very nice clean Screw Thread calculator copyright in 1935 by THE LUFKIN RULE CO. SAGINAW MICH. U.S.A. COPYRIGHT 1935 L.R.CO. The calculator is two piece, the top round section spins, for finding sizes of tap drills for NC and NF, also NPT on the back side, x 4.75 with a 2.75 diameter round section. It's in very good shape! Also included is a bonus decimal equivalents chard with a letter size drill chart on it also. Also in good shape for about the same era.

This is a nice clean Screw Thread calculator copyright in 1935 by THE LUFKIN RULE CO. SAGINAW MICH. U.S.A. COPYRIGHT 1935 L.R.CO. The calculator is two piece, the top section spins, for finding sizes of tap drills for NC and NF, also NPT on the back side, in diameter. It's in great shape!

This is a very nice, clean precision level with the working graduated, cut glass sight tube, that feature the rotating brass sleeve that can be turned to cover and protect the glass vial. The level glass is inside brass, and the sleeve is also brass, the holder frame is bronze and features (4) 1/4 clearance holes for screws to hold it down to machine tool or other moveable items that have to be leveled once on site, before use. This level is in great shape, and is accuate enought to be used as a small pocket bench level! The bronze base is marked CA 223804 , the A is inside the C, but I am not sure who made it, but most likely was made in the Cleveland or Akron Ohio area.

This is a very nice, clean bench or plumbing pipe plumb/level. The cast frame is 18 long, and has both the flat (bench) area, and the grooved area in the center of the bottom for round pipe or similar type work. This one feature the graduated main vial with the cutter glass graduations, plus three other vial, double plumb vials, and a cross test vial, all have cut glass marking, all are intact and working very well. This level has the black texture paint on the main casting with chrome plated fittings, including the chrome vial cover for the main top vial that can be turned to cover the vial with steel to protect it from damage. This feature also works very well. The chrome is about 95% intact, we note a few small dings at one end of the main chrome tube, where it attaches to the adjustable screws of the main frame, otherwise the cast is in very good condition, no rust, no cracks or damage, a few minor edge dings. Overall in very good used condition, a top quality bench level! It also comes with a hardwood fitted box, with good latches, and hinges. Very well made box with lap joints on the corners, in very solid condition, with some minor dings, nice finish, and good fitted pads for the level to set on. Very nice level and box overall!

This is a very good useable 6 flex rule marked NO. C306R THE L.S. STARRETT CO. ATHOL MASS. U.S.A. TEMPERED . It has inch graduations on one side, in 10ths and 50ths the other side is blank. It is in good straight condition with very good graduation lines and a nice flash chrome finish. About 99% like new!

This a very clean used spring inside caliper that is marked B , it matches the catalog No. 812-3. It measures 3 long from the center line of the pivot joint to the tips. It is in very good working order, good clean threaded rod, and solid nut, very good pivot joint, the spring is still strong. There is no rust, no pitting, no damage, light owner's markings noted on one side, and REC lightly etched on the other side, good tips. A quality made tool, by a well known maker!

This a very clean used spring inside caliper that is marked B , it matches the catalog No. 802-2. It measures 2.1 long from the center line of the pivot joint to the tips. It is in very good working order, good clean threaded rod, and solid nut, very good pivot joint, the spring is still strong. There is no rust, no pitting, no damage, and no owner's markings, good tips. A quality made tool, by a well known maker!

This a very clean used inside caliper that is marked THE LUFKIN RULE CO. SAGINAW MICH. MADE IN U.S.A. , it matches the catalog No. 142-5 discription. It measures 5 long from the center line of the pivot joint to the tips. It is in very good working order, good clean threaded rod, and solid nut, very good pivot joint, the spring is still strong. There is no rust, a few minor stained area, no damage, and no owner's markings. A quality made tool, by a well known maker!

This is a very nice, clean, heavy duty 4 capacity C-Clamp, marked J.H. WILLIAMS . This one is also marked WILLIAMS CO CC-404 DEEP THROAT CLAMP on the other side of the frame. The frame, threads and the whole clamp are in very good condition, very little wear, not rusty or bent up, only one small area has a clearence flat ground on it at an angle on the holding paw of the frame, and one other ground mark on the frame, both are minor issues. This clamp weighs over 3 pounds, and has an 8 long frame and the thickness at the clamp pad is 1-3/8 diameter, and the threaded screw is 3/4 diameter. The reach of the C frame is about 3 from the center of the threaded shaft to the edge of the frame. A very well made heavy duty C-Clamp by a well known tool maker, better known for quality automotive wrenches!

This is a nice clean, vintage 3-jaw drill, precision chuck marked CHUCK HARFORD CONN. MADE IN U.S.A. NO. 8-1/2N 0-1/4 CAP. JACOBS BALL BEARING SUPER CHUCK . It's in very good working condition with good jaws, adjusts smoothly, and runs true to center. No rust, no damage, very nice, slightly used drill chuck, arbor and key. The key for the chuck is included, and also in very good condition. The included arbor is .500 diameter. The arbor is also in very good condition.

This is a nice clean, vintage 3-jaw drill, precision chuck marked CHUCK HARFORD CONN. MADE IN U.S.A. NO. 8-1/2N 0-1/4 CAP. JACOBS BALL BEARING SUPER CHUCK . It's in very good working condition with good jaws, adjusts smoothly, and runs true to center. No rust, no damage, very nice, slightly used drill chuck, arbor and key. The key for the chuck is included, and also in very good condition. The included arbor has 3 different diameter, mainly for use with different collets size without having to change the collet in the machine to install the chuck. The arbor diameter sizes are .5 , .6 . The arbor is also in very good condition.

This is a nice clean antique 6 size outside spring caliper. It measures 7 long overall, the size (6 ) is measured from the center of the pivot joint to the tips. This caliper is marked GOODELL-PRATT CO. GREENFIELD MASS. U.S.A. . It has no former owner's intials or names on it. It's in very good working condition with very little wear, no rust or damage, very nice in the tip areas and the threaded areas. A good heavy duty caliper. Measures 7 long overall. Goodell-Pratt Co. was purchase by Millers Falls in 1931, so most tools marked GOODELL-PRATT were made before 1932.

Offering this a very nice clean 7 long wing divider marked BlECKMANN on the side of one leg as best we can read the lightly stamped steel. This one has very little wear, nice clean metal surfaces, no rust, and has good sharp points, very good pivot joint, ready to use. We do note a few dings and scratches, but none effecting the use of the tool or any of it's features. Features the fine adjustment, all steel pivot joint. All the screws and threads are in very good shape, including the good spring for the adjustment feature. One of the nicest we have seen in this style from the mid-1800's era! We did look up the name Bleckmann in the Toolmaker's directory for the 1800's era. We found this name listed as a maker of many types of cast tools, however they apparently didn't mark their tools with a location other than U.S.A., so we don't known what city their plant was in, or dates of opperation. We can tell by the way this tool is made, that it was from the 1800's era.

Offering this nice clean 8 long wing divider marked P.S. on the side of one leg. The letters stand for PECK, STOW, AND WILCOX, the same company that had the trade mark PEXTO , that they marked on some smaller tools. This one has little wear, some light pitting noted on the legs, and has good sharp points, very good pivot joint, ready to use. Features the fine adjustment, and brass / steel pivot joint. All the screws and threads are in very good shape, including the good spring for the adjustment feature. A top quality layout tool in it's day!

This is a nice clean 14 long chrome plated pipe wrench in very good condition. It is marked BEN HUR is believed to be a Store brand of the Van Camp Hardware Co. - Indianapolis, Indiana. It has very little wear, is not damaged or bent up, a few dings on the handle area, very good knurl wheel, threads, and jaws. We don't see many chrome plated pipe wrenches, so it makes this wrench even more rare! This one has the double couter-springs, all in very good shape! A rare and collectible pipe wrench!

This is a new old stock, electrian's side cutting pliers. They are marked UTICA U.S.A. 50-6 The suffix number tells the length, 6 long. They appear to have never been used, no wear, no rust, or pitting, all in fine, ready to use condition. This particular model has the inside jaw gripper serations on the jaws from the tip to about 1/2 back from the tip, and the side cutter section behind that, all in fine shape. The jaws width is .5 . The box is clean, solid with the exception of one side of the bottom of the box has two tears in it, the top is very good, minor wear, and has a good matching label. A hard to find model in fine shape!

Great Drafting tool set in original case, Made in Germany for Tecnical Supply Company Scranton and New York,It appears to be in great condition, i do not see any rust.